О сайте Карта сайта Обратная связь Версия для печати
INFO-AUTOGLASS.ru
Информационный гид
в мире автостекол
Email для связи:
 sergey@info-autoglass.ru
Интернет-Витрина
Автостекло
Автокаталоги
Инструменты
Сервисные услуги
Полезная информация
Вопрос-Ответ
Глоссарий
Статьи
Новости
Обратная связь

 

 
 

 
НОВЫЕ ПОСТУПЛЕНИЯ

Полезный инструмент для очистки U-образного паза

720 руб.

 

 
СПЕЦ. ПРЕДЛОЖЕНИЕ

Стекло опускное левой передней двери для Renault Megan sedan 95 г.

1 200 руб.

 

 
А ЗНАЕТЕ ЛИ ВЫ, ЧТО...

В современном автомобиле черные металлы составляют 60-70%, цветные металлы 6-7%, полимерные материалы (а к ним относятся клеи и герметики) 9-13%, текстиль 4%, стекло 3%.

Volkswagen Eos 2010


2010 Volkswagen Eos.

Windshield removal and replacement instructions
 

 Vehicle type: Two-door convertible

NAGS numbers*: Windshield part numbers FW2629 third visor, pre-applied adhesive system; FW2679 third visor, PAAS, rain sensor; FW2805 third visor, underside molding; and FW2809 third visor, underside molding, rain sensor

Helpful tools or supplies: New rain sensor or gel pack

A. Windshield
Preparation

1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure you have the right glass and moldings and that the urethane systems you are about to use are current. Windshield part numbers are FW2629, FW2679, FW2805 and FW2809.

2. Drape the fender with a fender cover and tape up any vulnerable areas on the vehicle to protect against possible damage. Tape up the defroster vents to prevent debris from falling into the openings.

3. Close the doors, windows and hood, and check operation of the rain sensor by sprinkling the rain sensor window with water. The wipers should wipe and then stop.

4. Remove the two-piece decorative cover from the base of the rearview mirror.

5. Release the rain-sensor retaining strap from the bracket’s sides.

6. Remove the windshield-wiper nut covers.

7. Remove the windshield-wiper nuts using a 13-millimeter wrench or socket. Lift the wiper up and off the wiper post.

8. Open the hood and remove the weatherstrip from the front of the cowl panel and firewall.

9. Beginning in one of the corners, use a plastic stick to pry upwards and release the cowl edge from the glass retainer at the base of the windshield.

10. The top and side moldings are exposed PAAS and far enough away from the pinchweld wall to cut out without damage. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers.

Removal
11. Make sure cutting blades are sufficiently sharp.

12. Before cutting out the windshield, remove contaminants from the glass and pinchweld to prevent contact with the urethane.

13. Tape up the vehicle body around the perimeter of the glass to avoid damaging the paint during cutout.

14. Use the cutting tools of your choice to remove the glass from the adhesive bead. If you use a power tool, lubricate the cutting area with water. Spray the top and sides; then make your cuts.

15. Take the windshield out of the opening using vacuum cups. Make sure the vacuum cups do not overlap a crack in the glass. Lift the glass and place it on a windshield stand or suitable workstation.

Installation
16. After cutting the windshield out, remove contaminants such as dirt, moisture and debris from the pinchweld. Clean the dashboard.

17. Dry fit the new glass to the opening. Mark your glass using a grease pencil or retention molding tape.

18. Place your vacuum cups on the new windshield in the appropriate location.

19. Set the windshield onto the old urethane.

20. With the windshield resting in the opening, make sure it is in the right spot.

21. Adjust both sides to the correct setting, marking the passenger side, then the driver side. Lift the glass and place it on a windshield stand or suitable workstation.

22. Follow the urethane manufacturer’s recommendations for installation.

23. Remove the shipping strip from the lower cowl retainer at the bottom of the glass.

24. Clean the inside of the windshield using a urethane manufacturer-recommended product. Do not touch the bonding area of the windshield after cleaning, prepping or priming it.

25. Wear powder-free Nitrile gloves to protect against harsh chemicals.

26. Apply the glass prep and primer following the urethane manufacturer’s recommendations.

27. Using the tool of your choice, remove the original urethane bead, leaving 1-2 mm of urethane on the pinchweld. Make sure there are no contaminants and do not touch the pinchweld after you have prepped the area.

28. Apply the pinchweld primer only to the areas where needed, and follow the urethane manufacturer’s recommendations. Allow preps and primers to dry as recommended by the urethane manufacturer.

29. Apply a triangular bead of urethane to the same path as the freshly cut urethane on the pinchweld. Before cutting your V-notch, cut the tip off of your nozzle with a nozzle-cutter. With the cut nozzle, measure to the top of the roofline, and at 1/16-inch higher than the roofline, make a mark on the nozzle with a pen or marker. Notch the nozzle up to the marked line; this will give you the appropriate triangular bead.

30. Lift the windshield from the windshield stand or workstation using vacuum cups. Set the windshield on the urethane at the mark you made during your dry fit. Lower the driver’s side of the windshield onto the urethane and line it up with the dry-fit mark; it is now in place.

31. The windshield is now ready to be decked. Press firmly to ensure a good seal.

32. Before re-installing the parts, check for leaks. Use a leak detector to go over the perimeter of the windshield. If you find a leak, apply more pressure or add more urethane to the spot and ensure that the glass makes contact with the wet urethane.

33. Re-install the removed parts in reverse order.

34. Allow the urethane to cure according to the urethane manufacturer’s recommended cure time before returning the vehicle to the customer. Warning: Disregarding the safe drive-away time that your urethane manufacturer recommends could jeopardize the structural integrity of the vehicle and the safety of its passengers.

35. You have completed the removal and replacement of the windshield.
 By Bob Beranek


Посмотреть другие статьи




 Наверх